System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
product
Bench top Dielectric Withstand tester
HYPOT III
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
product
Fully Automatic Eddy Current Crack Test System
ROTO-PUSH
Foerster Instruments, Incorporated
The ROTO-PUSH test station, which is integrated in production lines, serves to test cylindrical components for cracks in the liner surface. The testing configuration has to be rotated for automatic crack testing. After the test, the test pieces are sorted and separated. The continuous test run ensures a high testing rate, which increases profitability.
-
product
Electromagnetic Resonance High Frequency Fatigue Testing Machine
PLG Series
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system a...show more -
product
Structural Test ICP® Accelerometers
Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimi...show more -
product
Cable & Antenna Analyzer
CAA-100
ShinewayTech® CAA-100 cable & antenna analyzer can test Return Loss and VSWR of load’ frequency. Also can get Return Loss, VSWR of DTF (distance-to-fault) and Cable Loss. Users can be easy to know the connection of cable & antenna system is reliable whether or not. CAA-100 series with frequency range 25MHz-4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc. CAA-100 series is the necessary measuring instrument for the new generation of wireless network development, upgrade and maintenance.
-
product
Three Phase Phantom Load Test Bench
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
product
Microohmmeter
MMR-6700
The MMR-6700 digital meter is designed for measuring low resistances with a stabilised current of up to 200 A. The use of test clamps enables the safe measurement of breakers (high-, medium- and lowvoltage), isolators and other components earthed on both sides. The MMR-6700 series meters are equipped with a unique module in their class that measures inductive components which have a current of up to 10 A, enabling the winding resistance of motors, transformers and other inductive components to b...show more -
product
Compute Express Link (CXL)
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
product
Test for Model-in-the-Loop and Software-in-the-Loop
RT2
ETAS RT2 is a powerful test tool for testing of functional models (MiL) and software (SiL). It contains the following parts of the testing lifecycle: modeling, execution, assessment, and reporting. ETAS RT2 is specialized for testing of embedded systems with inputs and outputs of continuous or discrete signals. A model based test design approach enables intuitive realization of complex test strategies. Thanks to its capabilities ETAS RT2 enables comprehensive testing activities in the early phases of the development.
-
product
Small-size Reverberation Chamber
I-Series
The I small-size Reverberation Chamber Series is an amber gem set of OTA test chambers. With smart-stirring, the I-Series chambers have the smallest footprint in the market and are intended for IoT (LTE-M, NB-IoT and EC-GSM-IoT), MTC (LoRa, Sigfox), short-range radio technologies (BT 1.0/2.0, BLE, ZigBee, Z-Wave) and WLAN 802.11abgnac (2.4 and 5 GHz bands) for small devices up to 15cm and 5kg. The I-Series chambers provide for fast and accurate TRP, TIS, downlink and uplink Maximum Coupling Loss...show more -
product
MIPI M-PHY v5.0 Receiver Conformance Test Software
N5991MM5A
The Rx solution including Station Configurator and Valiframe maximizes the usage of test instruments, providing automated system calibration as well as conformance testing according to the M-PHY 5.0 test specification (CTS).
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on...show more -
product
Crank Angle Detector
PP/PA series
The Crank Angle Detection System is composed of a crank angle detector, a slit disk and a power box with built-in amplifier. By mounting the slit disk and crank angle detector to the crankshaft end of the engine, it enables to detect the rotation angle required for various engine performance tests such with high accuracy and high response.
-
product
FTL Test Block
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
product
Smart Card Testers
CT1000
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
product
MTM-IO-Serial: Software Controlled USB Hub and IO Module
As part of Acroname's MTM series, the MTM-IO-Serial module is a key component to manufacturing test systems for electronic devices using a standard USB 2.0 interface, serial UARTs and one or more interface voltages. The MTM-IO-Serial module features a software controlled USB hub (USB 2.0 high-speed) with four controllable channels. Each channel has switched data and 500mA current-limited power lines.
-
product
Regenerative Power System, 20 V, ±400 A, 5 KW, 400/480 VAC
RP7941A
The Keysight RP7941A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783367-01
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
product
Adhesion test with resuable 2.25" and 4" discs
ADHOR400R
The Adhor portable tester is ideal for your quality test on coating layer. It allows you to evaluate easily on the field the pull strength (commonly called adhesion) of your coating system on various substrates.
-
product
PMS Leak Test System
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
product
VNAs for Automated Test Equipment (ATE)
With our USB VNAs your automated test equipment works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
-
product
Battery Pack Drop Tester
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Drop Tester Relevant standards requirement:Test object: battery pack and systemTest procedure: The test object is most likely to fall in the direction of actual maintenance or installation. If it is not possible to determine the most likely fall direction, fall in the Z-axis direction, and the battery pack will fall from the height of 1 m to the concrete floor and observe for 2 hours.Accept standard: The battery pack or system has no electrolyte leakage, fire nor explosion.
-
product
Modulation Distortion Up To 50 GHz
S930705B
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Optics Test Systems
IR Autocollimator
Optik Elektronik Gerätetechnik GmbH
The infrared autocollimator was specially designed for the 1550 nm wavelength range. In conjunction with the CROSDETECT evaluation software, it achieves a measuring accuracy of 1 arcsec with a resolution of 0.1 arcsec. The camera used is suitable for the wavelength range from 900 nm to 1700 nm.
-
product
CPCI
Modules in compact PCI from Data Patterns are available for Data Acquisition and Control, Simulation, Communication Automatic test equipment, Rugged systems, Fail-safe systems, Computer controlled logic controls, Plant automation and similar requirements. Other I/O functions available from our IP and Mezzanine Module families can be directly integrated into our cPCI systems.Data Patterns has also pioneered cPCI derivatives such as 9U High Voltage systems, Multiple backplane support with Hot Standby Switchover capabilities. Continuous innovation enables MMI options such as CRT & LCD displays, Keyboards, Pointing devices, Finger print security devices and so on.
-
product
JIS/ASTM Standard-Compliant Plastic Bending Test System
Testing of Plastic in Accordance with JIS, ISO and ASTM Standards Can Be Performed
-
product
PXI System for LRU Test
ARINC 629
PXI System for LRU Test Support. The system shown here was developed in support of Boeing 777 LRU Production Test.
-
product
Transmission & Hydraulic Test Stands
Our equipment tests automatic and automated-manual transmissions. On and off-highway transmission test stands, transmission and hydraulic component test stands and valve body test stands. AIDCO Test Systems offers the latest in modern, electric motor and hydrostatically-driven transmission test stands. All units may include an air-cooled eddy current absorber (standard on the 450E), resulting in minimal dyno test cell noise and reduced maintenance.
-
product
Automated Laser Test System (ATE)
Lix is a class of instruments for automated laser beam profiling, power measurement and analysis with integrated machine vision.
-
product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.